|
Title: 3i INFOTECH TECHNICAL QUESTIONS - 1 Post by: Tanya on July 12, 2007, 08:40:47 PM 3i INFOTECH TECHNICAL QUESTIONS - 1
1. A 2MB PCM(pulse code modulation) has a) 32 channels b) 30 voice channels & 1 signalling channel. c) 31 voice channels & 1 signalling channel. d) 32 channels out of which 30 voice channels, 1 signalling channel, & 1 Synchronizatio channel. Ans: (c) 2. Time taken for 1 satellite hop in voice communication is a) 1/2 second b) 1 seconds c) 4 seconds d) 2 seconds Ans: (a) 3. A dishonest shopkeeper professes to sell pulses at the cost price, but he uses a false weight of 950gm. for a kg. His gain is ...%. 4. Max number of satellite hops allowed in voice communication is : a) only one b) more than one c) two hops d) four hops Ans: (c) 5. Conditional results after execution of an instruction in a micro processor is stored ina) register b) accumulator c) flag register d) flag register part of PSW(Program Status Word) Ans: (d) 6. Frequency at which VOICE is sampled is a) 4 Khz b) 8 Khz c) 16 Khz d) 64 Khz Ans: (a) 7. Line of Sight is a) Straight Line b) Parabolic c) Tx & Rx should be visible to each other d) none Ans: (c) 8. Purpose of PC(Program Counter) in a MicroProcessor is a) To store address of TOS(Top Of Stack) b) To store address of next instruction to be executed. c) count the number of instructions. d) to store base address of the stack. Ans: (b) 9. What action is taken when the processor under execution is interrupted by a non-maskable interrupt? a) Processor serves the interrupt request after completing the execution of the current instruction. b) Processor serves the interupt request after completing the current task. c) Processor serves the interupt request immediately. d) Processor serving the interrupt request depends upon the priority of the current task under execution. Ans: (a) 10. The status of the Kernel is a) task b) process c) not defined. d) none of the above. Ans: (b) 11. To send a data packet using datagram , connection will be established a) before data transmission. b) connection is not established before data transmission. c) no connection is required. d) none of the above. Ans: (c) 12. Word allignment is a) alligning the address to the next word boundary of the machine. b) alligning to even boundary. c) alligning to word boundary. d) none of the above. Ans: (a) 13. When a 'C' function call is made, the order in which parameters passed to the function are pushed into the stack is a) left to right b) right to left c) bigger variables are moved first than the smaller variales. d) smaller variables are moved first than the bigger ones. e) none of the above. Ans: (b) 14. What is the type of signalling used between two exchanges? a) inband b) common channel signaling c) any of the above d) none of the above. Ans: (a) 15. Buffering is a) the process of temporarily storing the data to allow for small variation in device speeds b) a method to reduce cross talks c) storage of data within transmitting medium until the receiver is ready to receive. d) a method to reduce routing overhead. Ans: (a) 16. Memory allocation of variables declared in a program is a) allocated in RAM. b) allocated in ROM. c) allocated on stack. d) assigned to registers. Ans: (c) 16. Memory allocation of variables declared in a program is a) allocated in RAM. b) allocated in ROM. c) allocated on stack. d) assigned to registers. Ans: (c) 17. A software that allows a personal computer to pretend as a computer terminal is a) terminal adapter b) bulletin board c) modem d) terminal emulation Ans: (d) 18. Find the output of the following program int *p,*q; p=(int *)1000; q=(int *)2000; printf("%d",(q-p)); Ans: 500 19. Which addressing mode is used in the following statements: (a) MVI B,55 (b) MOV B,A (c) MOV M,A Ans. (a) Immediate addressing mode. (b) Register Addressing Mode (c) Direct addressing mode 20. RS-232C standard is used in _____________. Ans. Serial I/O 21. Memory. Management in Operating Systems is done by a) Memory Management Unit b) Memory management software of the Operating System c) Kernel Ans: (b) 22. What is done for a Push opertion?Ans: SP is decremented and then the value is stored. 23. Binary equivalent of 52 Ans. 110100 24. Hexadecimal equivalent of 3452 Ans. 72A 25. Explain Just In Time Concept ? Ans. Elimination of waste by purchasing manufacturing exactly when needed 26. A good way of unit testing s/w program is Ans. User test 27. OOT uses Ans. Encapsulated of detect methods 28. EDI useful in Ans. Electronic Transmission 29. MRPII different from MRP Ans. Modular version of man redundant initials 30. Hard disk time for R/W head to move to correct sector Ans. Latency Time |